Valcom VIP-854 IP Tie Line
Valcom VIP-854 IP Tie Line Summary
Valcom VIP-854 (2 Channel)
Tie Multiple Non-IP Telephone Systems Together
The VIP-854 Networked Input & Relay Module allows passing of contact closures, which are software programmable to be either form A or form B, and initiation of VIP-601 server events over an IP-based LAN/WAN. Multiple VIP-854 Networked Input & Relay Modules can be used on the same network to create very large and distributed systems.
Mounting
The VIP-854 is designed for wall or table mounting.
Wall: Using the bracket and screws provided, secure the VIP-854 to the wall.
Table: Provided with the VIP-854 are four rubber pads. Peel the pads from their carrier backing and place at the four corners of the bottom of the unit.
Power Connections
The preferred method of powering a VIP-854 is via a power over Ethernet switch meeting the 802.3af specification.
If the rear panel barrel connector is used for power, the preferred power supply is a Valcom VIP-324.
Make all required signal connections before applying power to the unit. If powering via 802.3af, make sure all signal connections via the rear panel are made then connect the VIP-854 to the Ethernet switch.
If power is supplied via the barrel connector, make sure all signal connections are secure. Attach the unit to the network via the front panel RJ-45 Ethernet connector. Apply power by plugging the power supply in to the VIP-854 via the barrel connector on the rear of the VIP-854.
Network Connection
The VIP-854 has one CAT-5 RJ-45 network connector on the front panel.
Use the supplied CAT-5 patch cable to connect the VIP-854 to an Ethernet switch. If the Ethernet switch is 802.3af compliant the VIP-854 will draw power from it.
Signal Connections
On the rear panel, the VIP-854 has 2 RJ-11 jacks for connection to FXS circuits, 2 RJ-11 jacks for FXO circuits, 2 RJ-11 jacks for failover telephone connections and 1 terminal block for relay connections.
Phone1, Phone2: Connect standard analog Trunk lines to the VIP-854 via the rear panel RJ- 11 jacks labeled Phone1 or Phone2 (including standard analog telephones). Tip and Ring appears on pins 3 and 4 of these jacks. Line1, Line2: Connect standard analog Station circuits to the VIP-854 via the rear panel RJ-11 jacks labeled Line1 or Line 2 (including C.O. or Centrex phone lines). Tip and Ring appear on pins 3 and 4 of these jacks.
FP1, FP2: Connect a standard analog telephone to the VIP-854 via the rear panel RJ-11 jack labeled FP1 or FP2. Tip and Ring appear on pins 3 and 4 of these jacks. In the event of power failure, the telephone in FP1 will be able to access Line1 and FP2 will be able to access Line2.
Relay Connections: Access to the 2 form C relays is provided via a six pin screw terminal block. The relays are labeled K1 and K2. Each relay is brought out on three terminals. The common contact is the middle terminal with the normally closed contact on the left and the normally open contact on the right. Relay contacts are rated for 1A @ 24VDC.
Status Indicator Lights:
The VIP-854 has 3 status indication lights on the front panel:
STATUS: Flashes then illuminates to indicate power.
LINK: Indicates 100 Mbit Ethernet connection when illuminates. No activity indicates 10 Mbit connection.
ACT: Indicator flashes to indicate network activity.
| Valcom VIP-854 IP Tie Line |
-
Supports Telephone Systems that Do
- Not Provide Calling Party Supervision
- Use w/Analog, Hybrid, Digital Key Systems & PBX's
- Requires One Trunk Port (FXO) &
- One Analog Station Port (FXS) at EACH System
- Dial Select Desired Remote Office
- Auto Destination for Two Systems
|
| Valcom VIP-854 Features |
-
RJ-45 for network connection
- 2 RJ-11 FXO (Trunk) Ports
- 2 RJ-11 FXS (Station) Ports
- 2 Failover Phone Ports
- 2 Relays with Form C contacts
- Front Panel Status and Network LEDs
- Removable Screw Terminal Connector Provided For Input And Relay Interface
- 2.5mm Barrel Power Connector
- Power Over Ethernet 802.3af Compliant
|
